OE Ref.:
22853741
Commercial Name:
Schrader Snap-in 315MHz GM Global A ASK Basic
OEM Sensor P/N:
22853741
Ean Code:
EZ-sensor® coverage:
YES
Nut Torque:
Nm
Screw Torque:
11.5 in-lbs (1.3 Nm) Nm
Valve Core Torque:
3.5 in-lbs (0.4 Nm) Nm
Note:
WARNING: This product contains chemicals including lead, which is known to the State of California to cause cancer and reproductive issues.
For more information, go to
www.P65Warnings.ca.gov.
EZ-sensor® GO is pre-programmed for all vehicles mentioned in the list. No programming is required before installation for the below applications. Additionally, the sensor can be programmed to 99% of all vehicle makes, models and years.
Click on item for more details:
This list is being continuously updated.
Part No.:
1095
20018
20018
Commercial Name:
EZ-sensor Service Pack - Rubber Valve Assembly
Note:
20018 replaces 20008
Contents: 1 Rubber Valve Stem assembled with Plastic sealing cap and Valve Core, 1 Stainless Steel Attachment Screw,
Part No.:
1530
34000
34000
Commercial Name:
Schrader Service Pack - Aluminum Valve
Note:
Contents: 1 Aluminum Valve Stem, 1 Aluminum Nut, 1 Rubber Grommet, 1 Plastic Sealing Cap, 1 Nickel Plated Valve Core, 1 Stainless Steel Attachment Screw
EZ-sensor® GO can be programmed to any Make Model and Year shown in this list.
Click on item for more details:
This list is being continuously updated.
Relearn Summary: Stationary Relearn
Relearn DescriptionNOTE: If vehicle has an arrow pad located on the steering wheel, proceed to SCH-GM-22 WITH STANDARD IGNITION: NOTE: On some models, the turn signal will not illuminate once learn mode is active.
1. Turn the ignition to the ON/RUN position (engine off).
2. Using keyless entry system: press and hold lock and unlock buttons simultaneously until horn sounds, and then LF turn signal will become illuminated to indicate learn mode enabled. Or using the DIC, press and release INFO button until TIRE LEARN message is indicated on display. Hold down SET/RESET button until horn sounds, LF turn signal is illuminated to indicate learn mode enabled.
3. Starting at the LF tire, use TPMS activation tool to activate sensor, once the vehicle receives the signal from the sensor, the horn will chirp.
4. After horn sounds, proceed as in step 3 for the next 3 sensors in the following order: RF, RR, LR.
5. After LR sensor has been learned, turn ignition to OFF position. Adjust all tires to pressure listed on tire placard. Step one: press and hold the push button start until the vehicle is in accessary mode. Note: on Cadillac models you will know when you are in accessary mode when the Cadillac emblem appears on the DIC. NOTE: If Keyless entry system does not place vehicle into learn mode see SCH-GM-21/22 WITH PUSH-BUTTON START: NOTE: On some models, the turn signal will not illuminate once learn mode is active. 1. Press and hold the push button start until the vehicle is in accessary mode. Note: on Cadillac models you will know when you are in accessary mode when the Cadillac emblem appears on the DIC. 2. Press the MENU button located on the turn signal lever until “VEHICLE INFORMATION MENU” is displayed. 3. Once you are in the VEHICLE INFORMATION MENU, use the on the turn signal lever until the DIC displays the vehicle’s tire inflation pressures and positions. 4. Press and hold the button located on the end of the turn signal lever until “Are you sure that you want to relearn? YES or NO” is displayed. 5. Use the on the turn signal lever to highlight YES. Once YES is highlighted, press the button located on the end of the turn signal lever. The horn will chirp, “Tire Learning Active” will be displayed on the DIC, and the left front turn signal will be illuminated.
6. Beginning with the left front tire, use a TPMS activation tool to activate the left front sensor. Once the sensor has been activated, the horn will chirp and the right front turn signal will be illuminated. Repeat procedure in following order, right front sensor, right rear sensor, and finally the left rear sensor. Once the left rear sensor has been activated, the horn will chirp twice. You can then turn the vehicle off to exit “learn mode.” • Troubleshooting Tip: On many vehicles, the option to relearn the TPMS by accessing the DIC will not work. Be sure to obtain keyless entry transmitter from customer, or some scan tools have the ability to place the vehicle into learn mode or write IDs via an OBDII connection.
Relearn Procedure as PDF document
Mounting Instructions
Note:
Sensor images shown in this document are for illustration purpose only!
Phisical sensor body may be different.
Non contractual document!
For tecnical information, please contact your supplier or leave a message at info@Schrader TPMS E-Catalog.com
User Manual/Quick Start Guide
Note:
Document contains full description user manual and / or Quick Start Guide. Non contractual document!
For technical information, please contact your supplier or leave a message at SchraderNA@sensata.com
Approvals and Declarations
Note:
Package contains FCC, IC and CE certifications
Physical sensor body may be different.
Other documents can be also found
here.